Heavy duty toggle bolts for metal studs

Crimson AV HT4 Toggle Bolts, For use to Attaching to Metal Studs, Used as Accessory to Attach WA Shelves Directly to Drywall, Comes with 1/4 x 2 1/2" Machine Bolt, Pack of 4

or use to attaching to metal studs where specified in product manual. Also for used as accessory to attach WA shelves directly to drywall

• Hardware pack of toggle bolts
• Mounts to drywall
• Comes with 1/4 x 2 1/2" Machine Bolt

• Mounting surface: drywall
• Hardware: drywall toggle
• Color: Silver
• Model number: HT4 (four-pack)

Specifications are often supplied by manufacturers that detail specific mounting tools, materials and methods recommended for anchoring their products. Follow these guidelines whenever possible. Choose the correct size and length of toggle bolts to carry the intended load. Websites like Toggle.com can help calculate the correct size and length.

Warning

Make sure that there are no electric wires in the area where drilling into the wall occurs. Always wear safety glasses when drilling into metal studs to protect from flying metal fragments.

Heavy televisions are commonly mounted on walls.

Using toggle bolts is a common way to anchor heavy objects into steel studs. Some prior knowledge of the existing materials -- thickness of the drywall, gauge of metal studs and spacing of metal studs -- will aid in determining the best mounting methods. For best results, heavy objects should be mounted to as many metal studs as possible so that the weight will be evenly distributed. Knowing the weight of the object to be mounted will aid in determining the number and size of the toggle bolts needed to complete the task.

Video of the Day

Step 1

Use the stud finder to locate the studs where you will be mounting the object. Mark the wall with a pencil to indicate their location. Metal studs for interior non-load-bearing walls are usually 1 5/8 inches wide, so try to put your marks in the center of the stud.

Step 2

Measure up the wall with the tape measure to the height where the object will be mounted. Mark that spot with the pencil.

Step 3

Center the mounting bracket on the marks on the wall. With a pencil, mark through the holes in the mounting bracket where the toggle bolts will go. Make sure that the bracket is level and centered on the studs before marking.

Step 4

Drill holes in the wall and through the metal studs where you marked the wall with the mounting bracket. The size of the drill bit should be large enough to allow the toggle bolt to gain access through the hole. Check the toggle bolt manufacturer's recommended bit size.

Step 5

Attach the mounting bracket to the wall using the toggle bolts. Slide the toggle bolt through the hole and pull securely to the metal stud. Screw each bolt so that it's snug, but not tight to the bracket. Once all the bolts are secure, check to make sure the bracket is level before tightening the bolts fully. If level, tighten the toggle bolts completely.

SNAPTOGGLE® anchors get their name from their speed and ease of use as they work in a SNAP! Unlike other anchors, this system does not require the bolt or the bracket for initial installation. Simply drill a 1/2" 12mm hole and insert the metal head, then zip tight and its held in place. New longer and stronger plastic straps that work in base materials 10mm to 90mm thick. Excess straps made to snap-off flush with the wall every time, assuring precise alignment. You are now ready to attach the fixture with 1/4" bolts to length required (sold separate). Exceeds most building requirements supporting inexcess of 100Kg per bolt (depends on wall). Made from premium grade materials in the USA for reliable long-life corrosion resistant service . Strong enough for grab-bars, shelving, mirrors, drapes, curtains, fans, and flat-screen TVs.

• Pre-assembled and ready for immediate use
• Pre-installs without requiring fixture or bolt
• Far superior to wing toggles, holds twice the load
• Trivalent B633-85 III/Sc zinc plating RoHS compliant
• Automatically adjusts to thickness of wall or ceiling
• Plastic straps suit Wall thickness; 10mm to 90mm
• Holding weight: Drywall 12mm 120Kg, 16mm 160Kg
• Pre-drill hole = 1/2" 12mm (smaller than springwing)
• Minimum clearance behind wall is ~50mm
• Requires 1/4"-20 imperial bolt sold separate

Order CodeBB24014Size1/4"

Bulk Buy: $2.65 for 10 or more

BB24014 - H/D HOLLOW WALL ANCHORS

Bulk Buy: $2.65 for 10 or more

Order CodeTS14X212Diam.6.35mmØLength63.5mm

Order CodeTS14X3Diam.6.35mmØLength76.2mm

Order CodeTS14X4Diam.6.35mmØLength101.6mm

TS14X212 - TOGGLER SCREW 1/4" X2.5"

TS14X3 - TOGGLER SCREW 1/4" X 3"

TS14X4 - TOGGLER SCREW 1/4" X 4"

Contact us for Bulk Buy and Project Based Pricing for HEAVY DUTY HOLLOW WALL ANCHORS 1/4" - TOGGLER® SNAPTOGGLE®

Enter Email Address Enter Valid Email

Submit Reset

Success! Thanks for your enquiry. Our Customer Sales Team will be in contact with you Shortly.

BB24014 - Product Downloads

Please contact us with your download requirements,e.g. User Manual, Data Sheet, etc and will get back to you.

Can I use toggle bolts on metal studs?

How much weight can a toggle bolt hold in metal studs?

How do you anchor heavy objects to metal studs?