The drain filter’s location varies depending on the type of a washer and the model you are using. In most top-loaders, the drain pump filter can be accessed by pulling out the drawer that is usually located at the front of the washer on the lower right-hand side. The drain filter usually exists within the drain pump valve to protect the drain pump
from possible damage that can be caused by debris and foreign objects such as coins, pins, screws, etc. in wastewater. Foreign objects such as pins, screws, and coins enter the washer through your clothes pockets and drain out through the hoses, which later get trapped by the drain filter. While the modern-day washers (front load and top load) do not have
lint filters separately as they operate on self-cleaning pump filters, there is always a possibility of lint accumulation in the drain pump filter areas. TIP: In order to get a precise location of the drain filter, you may simply refer to the user manual of your washer. Also Read:
Where is the Lint Trap located in the Whirlpool Washing Machine? Functions of the drain filterThe most common functions of the drain filter are mentioned below:
Final ThoughtsTo get precise placement of the filters or any other components of the washer, it is always a good idea to refer to the user manual. Cleaning the filters timely is always a good practice. Also Read: How to take the Drum out of Washing Machine? Frequently Asked QuestionsHere are some common questions that are asked repeatedly. How do I manually drain my washer?Manual draining is usually performed in situations when the washer stops draining due to a possible clogging or when a manual inspection of the drain system is required. In order to perform manual draining, you simply need to turn on the manual operating lever located near the drain pump valve. Why is my washer draining at a slower pace?Washer draining at a slower pace may be caused due to a few common factors such as a clogged drain hose, malfunctioning drain pump, etc. You may need to inspect the drain area for a possible clog and clean them accordingly. A faulty drain pump may not be able to generate enough pressure and may need a replacement. Always consult an expert for the inspection of the drain pump. You May Also Like
 How to understand that the problem is in the pump?If there are problems with the pump, a number of characteristic signs will appear, by which you can easily determine that the pump is malfunctioning. Among them:
What caused these “symptoms” in your washing device? We already realized that pump clogging is to blame for everything, but why is it happening? The fact is that the drain path must be cleaned periodically, and if this is not done, all garbage that gets there when washing clothes (hair, dust, threads) or from the drain pipe gradually clogs the pump. Also, some cheap detergents are poorly soluble, and precipitates formed after their use also remain in the tract. This subsequently leads to failures. Prepare the machine for repairSo, open the instructions and carefully look at where the pump of the Whirlpool washing machine is located, so as not to spend a lot of time searching for it and not damage other details. If you are sure that you figured it out, prepare two types of screwdrivers: a flat and a Phillips screwdriver, as well as an open-end wrench and some kind of flat container. A container is needed so that water from the pump does not spill onto the floor. First of all, disconnect the unit from the mains and water supply for your own safety in order to avoid unforeseen problems.
Now you can proceed directly to the dismantling. Open the small door on the skirting board of the washer (it is located in front from the bottom). There is a filter. Unscrew it carefully with counterclockwise movements. Depending on the model, the filter can still be secured with an additional bolt. Then unscrew it with a screwdriver! We clean the pumpThe pump is located at the bottom of the machine, one might say, at the bottom. Sometimes the bottom of the machine is not covered by anything, and sometimes manufacturers attach an additional panel there. To get to the pump, you need to remove it. You can also put the machine in a position convenient for you to freely interact with the contents of its lower part. The design of the pump consists of two parts: the so-called snail and the pump itself with an impeller. In order to clean it, the structure will need to be disassembled, but this is not difficult at all: unscrew a few screws that connect the parts. Now you can carefully examine the impeller. Usually, therein lies the problem: all the garbage wraps around it and prevents the pump from functioning normally during operation. Remove litter from it, collect the pump and put it in place. Set the machine to its original position, connect it to all communications and start washing, so that later you can see how the water drains. If all is well, then you did it. If the problem persists, then the pump must be changed: it is out of order. Here are some simple rules to avoid premature pump breakdown.
That's all! In fact, it’s not so difficult to maintain the state of your home assistant, you just need to do this regularly, otherwise worse problems will appear! Where is the drain pump on Whirlpool washer?Unscrew the three screws at the bottom of the panel, using a Phillips screwdriver. Remove the panel. The drain pump assembly is directly in front of you, in the middle of the machine.
How do you unclog a washing machine drain pump?The drain pump is near the bottom of the machine, and it's in a translucent housing, so you should be able to see if a sock or some other item is lodged in it. If so, you can remove it with needle-nose pliers after disconnecting the drain hose by loosening the clamp with a screwdriver.
|
How to clean drain pump on whirlpool washer
Postagens relacionadas
direito autoral © 2024 cemle Inc.
