This mount will accept most Docter style RDS, such as the Vortex Venom/Viper, Leupold Deltapoint (does not fit new Deltapoint Pro), and Burris FastFire 3. We consider these red dot sights for those that do not want to break the bank, but still need a sight they can rely on for home defense/range days. As with all of our other mounts, you will obtain a solid cheek weld that allows for proper weapon control and rapid target engagements. Made from 6061-T6 aluminum and backed by our lifetime, no b-s warranty, this combo is sure to satisfy those looking for a inexpensive but capable optic for their PS90. Show All orders come supplied with the hardware needed to secure the mount to receiver and optic to mount. Once you remove your old sight/rail, it takes no time at all to install any of the available units. Last step is to dial her in and now you've got an ideal optic setup for home defense or range day plinking! Please note that FN casts their receivers for the P90/PS90 so the tolerances within the receiver are like snowflakes, no two are identical, and can be tens of thousandths different. Thus fitting a precision part into said receiver will have varying results. If your mount happens to be extremely tight (to the point of beating it in with a hammer), give us a call and we will shave down the sides/repaint it for no charge. *For a bead blasted, unpainted product, giving you the ability to paint it yourself, we provide this product 10% off. Use discount code "NOPAINT" at checkout. (Product will come sand blasted and unpainted). *For this mount to work with the Holosun 407K and 507K, the rear pins on the mount MUST be removed by milling or filing. This mount has a bottom radius of .670". There should be a slight gap at the top of the radius between the receiver and the mount when mounted. The four spreads on this mount measure: Shotgun:
EGW red dot mounts are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install.\ Simply remove the rear sight on your pistol and replace it with the EGW mount in order to mount your Vortex Viper/Venom, Burris FastFire, Crimson Trace CTS-1200, CTS-1300, US Optics DRS 2.0 and 2.0 Enhanced, or Doctor red-dot sight. No alterations are required. You can take our mount off and replace your rear sight at any time. Mounting hardware included.
Our red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install. Installation: EGW recommends 15 inch lbs of torque and a drip of blue loctite. Rear sight pusher tool recommended for installation. Notes: Sig M17 M18 P320 49201: This mount fits: This mount does not fit: HK VP9 / VP9L Optics Ready 49287: This mount fits HK VP9 Optics Ready Models, VP9 Optics Ready, VP9L Optics Ready, VP9 Tactical Optics Ready. Walther Q5 Match 49288: This mount fits: Walther Q4 Steel Frame OR, Q4 Tac M1, Q4 Tac M2, Q5 Match M1, Match M2, Match Steel Frame Standard, Match Steel Frame Professional, Q5 Match Steel Frame Standard 10R Walther PPQ 22LR 49293: This mount fits the Walther PPQ .22LR. This mount does not fit: Walther PPQ 22, Walther PPQ Q4 Tac, Walther Q5 Match. The PPQ sight has a hole drilled in the bottom of the dovetail to accomodate the plunger on some models of the Walthers. This plunger may also be removed from the slide if desired. Walther PPQ 49295: This mount fits the following Walther models: PPQ Classic (M1), PPQ M2 (All Models), PPQ 45, PPQ 45 SD, PPQ Sub Compact, P99 (All Models), PPX (All Models), Creed, Creed 10 Round, PPS (All Models), PPS M2 (All Models). This mount does not fit: Walther PPQ 22, PPQ Q4 Tac, Q5 Match The PPQ sight has a hole drilled in the bottom of the dovetail to accommodate the plunger on some models of the Walthers. This plunger may also be removed from the slide if desired. S&W 1911 ADJ SIGHTS 49296: Will fit S&W 1911 with Adjustable Rear Sights, will not fit models with fixed rear sights. DESERT EAGLE (POST 2017) 49297: Please take note of the Pre 2017 and Post 2017 differences before placing your order: Pre 2017 rear shelf behind the dovetail is .187″. Post 2017 rear shelf behind the dovetail is .120″ CZ 75 SP-01 Shadow 49298: This mount fits: CZ 75 Shadow, CZ 75 SP01 Shadow, CZ Shadow 2 Sig P210A 49299: This mount fits: Sig P210A Target This mount for the P210 is made specifically for the U.S. made P210s. The front of the mount will need to be cross drilled to fit each individual gun. The pin from the factory rear sight may be reused as well. The hole dimension for the cross hole is 2.04mm. There are 2.04mm drill bits available from sites like Grainger, but you may also be able to use a 5/64″ bit to mark the hole on the mount and a 3/32″ bit to drill the hole. Sig uses a 2mm coiled spring pin to hold the original sight in place. LPA LOW MOUNT 49301: This mount fits: Baby Desert Eagle (Post 2006), DESERT EAGLE (PRE 2017) 49303: Please take note of the Pre 2017 and Post 2017 differences before placing your order: Pre 2017 rear shelf behind the dovetail is .187″. Post 2017 rear shelf behind the dovetail is .120″ FN, FNS, FNX 49304: This mount does not fit the FN Five-seveN (5.7) H&K USP 49305: DOES NOT FIT THE USP COMPACT. The USP Compact rear sight cut depth is .200″, The standard USP (for this rear sight cut) rear sight cut depth is .160″ This mount fits: USP Tactical 9mm, USP Tactical .45 ACP, USP 9mm, USP 40 S&W, USP .45 ACP. Does NOT Fit: USP Expert, USP Elite. EAA SS, TANFOGLIO WITNESS 49306: This mount fits: EAA / Tanfoglio Witness with adjustable rear sight (windage AND elevation). This mount does not fit: EAA / Tanfoglio Witness with fixed rear sight S&W M&P 49308: This mount will fit: Smith & Wesson M&P Full Size, 2.0 Full Size, 22 Full Size, Compact, 2.0 Compact, SD9VE, SD40VE. This mount does not fit: Smith & Wesson M&P Shield, Shield EZ .380, SW9VE, SW40VE, C.O.R.E Series, M&P .22 Compact. Smith and Wesson’s rear sight dovetails are known to vary in dimensions. Our sights are made to the same tolerances. Some users may have trouble installing our plate on their slide due to the varying tolerances in your slides. Please keep this in mind when ordering. Our return policy does allow for returns of unused and undamaged parts. These mounts should be installed and checked by a qualified gunsmith. No liability is expressed or implied for damage or injury which may result from improper installation or use of this product. S&W 52 49309: This mount fits: Smith & Wesson Model 52 This mount does not fit: Smith & Wesson Model 41 GI 1911 49310: This mount will fit: 1911s with a G.I. style rear sight cut, and the following Iver Johnson firearms 1911A1, 1911A1 9, Falcon 45, Thrasher 45, Thrasher 9, 1911A1 Chrome 38W, 1911A1 Chrome 38P, 1911A1 CHRW45, 1911A1 CHR45P, 1911A1 CHR45WP, 1911A1 Zombie, 1911A1 Copperhead, 1911A1 Water Moccasin, 1911A1 Boa, 1911A1 Muddy Girl 9mm, 1911A1 Digital Navy, 1911A1 Digital Snow 45acp. NOVAK 49311: This mount will fit pistols with a Novak Cut rear sight mount such as STI fixed rear sights, Springfield Armoury 1911, GSG 1911, Rock Island, Iver Johnson, and Wilson Combat. CHECK YOUR PISTOL HAS A NOVAK CUT SIGHT BEFORE ORDERING. Minor modification to the sight base may be necessary for Rock Islands and GSG 1911 .22s. BOMAR 49312: This mount will fit pistols with a Bomar Cut rear sight mount such as the STI Edge (Bomar Cut Version), Les Baer 1911 (adjustable rear sights), Colt Gold Cup Trophy with Bomar Rear Sight Cut, Colt Gold Cup National Match .45acp, Colt Gold Cup National Match 9mm, Springfield TRP Operator. CHECK YOUR PISTOL HAS A BOMAR CUT SIGHT BEFORE ORDERING. GLOCK 49313: This mount fits all generation Glocks: 17, 19, 20, 21, 22, 23, 24, 26, 27, 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, 39, 41, 42, 43, 46, as well as the Canik TP9SF, Bersa BP9CC, Tactical Solutions .22lr Conversion, Advantage Arms .22lr Conversion Does not fit the following Glock MOS models: Glock 17 Gen 4 MOS, Glock 19 Gen 4 MOS, Glock 34 Gen 4 MOS, Glock 40 Gen 4 MOS, Glock 41 Gen 4 MOS, Glock 35 Gen 4 MOS, Glock 34 Gen 5 MOS. KIMBER and RUGER 1911 49316: This mount fits: Kimber 1911 (with adjustable rear sights for windage and elevation), Ruger SR1911 (with adjustable rear sights for windage and elevation). Will not fit models with fixed rear sights. LPA 49317: This mount will fit pistols with an LPA Cut rear sight mount such as Sig Sauer 1911, STI adjustable rear sights, Springfield Armoury, Rock Island, Iver Johnson, CHECK YOUR PISTOL HAS A LPA CUT SIGHT BEFORE ORDERING. Will Not Fit: Para Elite LS Hunter, Remington R1 10mm Hunter SIG SAUER 49318: THIS MOUNT DOES NOT WORK WITH ANY SIG OPTICS READY PISTOLS (P320 X-CARRY ETC.) This mount fits (including but not limited to): Sig #8 Sights, P220, P224, P225, P225-A1, P226, P227, P228, P229, P238, P239, P245, P320, P938, SP2022, M11-A1, MK25, Bersa Thunder UC Series (9/40/45), Bersa Thunder HC Series (9/40/45), FN 509. This mount does not fit: Sig 1911s, Any Optics Ready Sigs i.e. P226 Legion RX, P229 RX, P320 X-Carry etc., P210 Target, P365, FN 509 Tactical. S&W REVOLVERS 49319: This mount will fit K, L, N, and X frame Smith & Wesson Revolvers. If your revolver is not drilled and tapped this mount will not work. The best way to verify that it is/is not drilled and tapped is to open the cylinder and check the rib underneath. There should be through holes that are drilled and tapped. If there are not this mount will not work without you having the gun drilled and tapped. RUGER REVOLVER 49320: This mount fits the following Ruger Revolvers: Blackhawk, Redhawk, GP100 (with adjustable rear sights), GP100 Match Champion. This mount does not fit: Ruger Flattop Revolvers RUGER AUTO 49321: This mount fits the following Ruger pistols: Ruger MK I, MK II, MK III, MK IV, P85, P89, P90-95, P97, 22/45 COLT GOLD CUP 49322: This mount fits the following Colt models: Gold Cup, This is for Colt models with the Elliason style adjustable rear sight. The elevation screw from the original rear sight is re-used in the center hole on this mount. SPRINGFIELD XD 49323: This mount fits the following Springfield XD models: XD MOD.2 – 3″ SUB-COMPACT MODEL, XD MOD.2 – 3.3″ SUB-COMPACT MODEL, XD MOD.2 – 4″ SERVICE MODEL, XD MOD.2 – 4″ SERVICE MODEL THREADED BARREL, XD MOD.2 – 5″ TACTICAL MODEL, XD 3″ SUB-COMPACT MODEL, XD 4″ SERVICE MODEL, XD(M) 3.8″ COMPACT MODEL, XD(M) 3.8″ MODEL, XD(M) 4.5″ MODEL, XD(M) 4.5″ THREADED BARREL MODEL, XD(M) 4.5″ OSP FULL SIZE, XD-S 3.3″ MODEL, XD-E 3.3″ SINGLE STACK It does not fit: XD(M) 5.25″ COMPETITION SERIES MODEL Universal 0.468″ RAD 49324: This mount has a bottom radius of .468″. There should be a slight gap at the top of the radius between the receiver and the mount when mounted. The two spreads on this mount measure .500″-.505″ and .8625″. This should fit barrel/receiver diameters from .936″-1.350″. UNIVERSAL 0.670 RAD 49325: This mount has a bottom radius of .670″. There should be a slight gap at the top of the radius between the receiver and the mount when mounted. Note that this mount is drilled for and only includes #6 screws. If your application requires #8 screws then you will need to source these screws yourself as well as have this mount drilled to suit #8 size screws. The two spreads on this mount measure .500″-.505″ and .8625″ which should fit the receiver ring on the following guns: Shotgun: Mossberg 500, 590, 835, 930, 935 Pre ’97, Mossberg 500, 590, 835, 930, 935 Late (after ’97) (Requires 8-40 and Longer Screws), Benelli Auto / Super Black Eagle / Vinchi, M2 (Will Work in the Front Set Only, 8-40 Screws), Benelli Supernova (Will Work in the Front Set Only, 8-40 AND Longer Screws), Browning A-Bolt 12 Gauge, Savage 210, Savage 212, Savage 220, Stoeger M3000 / Stoeger M3500 (Will Work in the Front Set Only, 8-40 Screws), Winchester 1300, Winchester SXP Rifle: Remington 700, 722, 40x, Remington 783, Remington 710/770, Remington xp 100, Remington 4, 6, 7400, 7615 (Front Set Only, 8-40 Screws), Savage Arms Centerfire Models, Winchester 70. CZ 75 49326: This mount fits the following CZ models: 75, 75 SP-01, 75 SP-01 Phantom, 85, P-01, PCR. This mount does not fit the CZ P-07 or CZ P-09 (Does NOT fit any of the SP-01 Shadow variants) S&W M&P 22 COMPACT 49327: Using this mount in combination with a red dot sight will increase the weight on the slide of your firearm. This may lead to cycling issues especially in .22s. SIG 220 10mm HUNTER 49328: This mount fits: Sig P220 10mm Hunter, Sig P220 Super Match SAO, Sig P220 Match Elite (with adjustable sights). S&W 1911 FIXED SIGHTS 49330: Will fit S&W 1911 with Fixed Rear Sights, will not fit models with adjustable rear sights. MARLIN 1894 49331: This mount is comes with both #6 and #8 screws and is drilled to suit both screw sizes. This mount fits: Marlin 1894, 1895, Henry H009, H010, H014, H006, H012 Golden Boy, Camp Carbine 9mm, Camp Carbine 45, Ruger PC Carbine.
Available for the following: #49201: Sig P320 M17 #49287: HK VP9 / VP9L Optics Ready #49288: Walther Q5 Match #49293: Walther PPQ 22LR #49295: Walther PPQ M2 #49296: S&W 1911 with Adjustable Rear Sights #49297: Desert Eagle (Post 2017) #49298: CZ 75 SP-01 Shadow and Shadow 2 #49299: Sig P210A Target #49301: LPA Low Mount Cut Rear Sight #49302: Colt 1911/22 Rail Gun with the Walther Slide #49303: Desert Eagle (Pre 2017) #49304: FN, FNS, FNX #49305: H&K USP #49306: EAA Super Sight, Tanfoglio Witness with Adjustable Rear Sight #49307: H&K VP9, VP9SK, VP40, P30, P30L, P30SK, HK45, HK45C #49308: S&W M&P #49309: S&W 52 #49310: 1911 with GI Style Cut Rear Sight #49311: Novak Cut Rear Sight #49312: Bomar Cut Rear Sight #49313: Glock #49315: Kimber 1911 with Fixed Rear Sights #49316: Kimber 1911 and Ruger SR1911 with Adjustable Rear Sights #49317: LPA Cut Rear Sight #49318: Sig Sauer P220-229, 320 #49319: S&W Revolvers, K, L, N and X Frames #49320: Ruger Revolvers #49321: Ruger Auto (Mk 1, Mk 2, Mk 3, Mk 4, P85, P89, P90-95, P97, 22/45) #49322: Colt Gold Cup, Python, Anaconda #49323: Springfield XD #49324: Universal Fit for 0.468″ Radius for Rifles and Shotguns #49325: Universal Fit for 0.670″ Radius for Rifles and Shotguns #49326: CZ 75, 75 SP-01, SP-01 Phantom, 85, P01, and PCR (Does NOT fit SP-01 Shadow variants) #49327: S&W M&P 22 Compact #49328: Sig Sauer 220 10mm Hunter #49329: CZ P-10 C #49330: S&W 1911 with Fixed Rear Sights #49331: Marlin 1894, 1895, Henry H009, H010, Ruger PC Carb
ATP is an authorised Australian dealer for EGW. All EGW products bought from ATP are covered by EGW’s Australian Warranty. Weight0.101 kgPart Number#49201 Sig M17, M18, P320, #49287 HK VP9 Optics Ready, #49288 Walther Q5 Match, #49293 Walther PPQ 22LR, #49295 Walther PPQ M2, #49296 S&W 1911 Adj Sights, #49297 Desert Eagle Post 2017, #49298 CZ 75 SP-01 Shadow, #49299 Sig P210A Target, #49301 LPA Low Mount Cut, #49302 Colt 1911/22 RG Walther, #49303 Desert Eagle Pre 2017, #49304 FN, FNS, FNX, #49305 H&K USP, #49306 EAA, Tanfoglio Witness, #49307 H&K VP9, VP9SK, VP40, #49308 S&W M&P, #49309 S&W 52, #49310 1911 GI Cut Rear Sight, #49311 Novak Cut Rear Sight, #49312 Bomar Cut Rear Sight, #49313 Glock, #49315 Kimber 1911 Fixed Sights, #49316 Kimber 1911 Adj Sights, #49317 LPA Cut Rear Sight, #49318 Sig Sauer P220-229, 320, #49319 S&W Revolvers, K, L, N, X, #49320 Ruger Revolvers, #49321 Ruger Mk 1, 2, 3, 4, 22/45, #49322 Colt Gold Cup, Python, #49323 Springfield XD, #49324 Universal Fit for 0.468" Radius, #49325 Universal Fit for 0.670" Radius, #49326 CZ 75, Phantom, P01, P07, #49327 S&W M&P 22 Compact, #49328 Sig 220 10mm Hunter, #49329 CZ P-10 C, #49330 S&W 1911 w Fixed Sights, #49331 Marlin 1894, 1895, Henry H009, Ruger PC Carb What mount does the vortex venom use?Vortex Venom features the Docter/Noblex mounting standard. Here, you can see the dimensions and the photo of the footprint.
What footprint is the Burris FastFire?ACC-009 4x32 BROWE Mini Red Dot Mount - DOCTER Footprint (fits DOCTER, Insight, Burris Fast Fire and other models with Docter Footprint)
What optic has the same footprint as vortex venom?The Viper and Venom red dot sights from Vortex Optical look similar. They share many characteristics. These sights share the same Vortex quality of design and construction. The Viper sight is slightly smaller than the Venom, but not appreciably.
Can you mount a vortex venom on an RMR cut?The EGW red dot sight mount adapter plates for the RMR Cut Zev Slides are meant to be installed directly on the slide. Simply remove the sight plate on your gun (if applicable) and replace it with our mount in order to mount your Vortex Viper, Vortex Venom, Burris FastFire, or Docter red-dot sight.
|
Will Burris Fastfire Mount fit Vortex Venom?
Postagens relacionadas
direito autoral © 2024 cemle Inc.
