OSHA requires workers to wear a full-body harness, (one part of a Personal Fall Arrest System) when they are working on a suspended scaffold more than 10 feet above the working surface, or when they are working in bucket truck or aerial lift. Show
When working on a suspended scaffold 10 feet or higher above the working surface or in a bucket truck or aerial lift what safety device should you wear quizlet?When working on a suspended scaffold 10 feet or higher above the working surface, or in a bucket truck or aerial lift, what safety device should you wear? … These include using fall protection equipment and using ladders safely. Each end of a platform 10 feet or less in length shall not extend over its support more than 12 inches (30 cm) unless the platform is designed and installed so that the cantilevered portion of the platform is able to support employees and/or materials without tipping, or has guardrails which block employee access to … What are the ways an employer can protect workers?Guardrail and safety net systems are two ways to protect workers from falls on the job. If workers are more than 6 feet above the lower surface, some type of fall protection must be used by the employer. midrails, screens or mesh are installed when there are no walls at least 21 inches high. What protective device is required for a floor opening that measures at least 12 inches?Provide covers and/or guardrails to protect workers from the hazards of open pits, tanks, vats, ditches, and the like. An opening measuring 12 inches or more in its least dimension in a floor, platform, pavement, or yard, through which persons may fall. Standard railing. Consists of top rail, mid rail, and posts. Did the employer use a disciplinary program to retaliate against Carla?Did the employer use a disciplinary program to retaliate against Carla for reporting a workplace injury? … His employer disciplines Ricardo for failing to report his injury “immediately” as required by the employer’s injury reporting rules. What should your first action be upon finding a safety hazard in your workplace select the best option?What should your first action be upon finding a safety hazard in your workplace? Contact your team leader, supervisor, manager, etc. At what height is fall protection required on scaffolds?The standard requires employers to protect each employee on a scaffold more than 10 feet (3.1 m) above a lower level from falling to that lower level. What is the minimum height at which guardrails are required on scaffolding?The minimum guardrail height for scaffolds manufactured or first placed in service after January 1, 2000 is 38 inches. For all scaffolds, the maximum height is 45 inches. Are toeboards required on scaffolding?Scaffolding. Most scaffolding more than 10 feet off the ground should have toeboards at least four inches high on all open sides of the scaffolding, according to OSHA guidelines. Ship scaffolding, however, can have three-quarter inch by one-and-a-half inch edges rather than standard four-inch toeboards. What are the 4 high hazard areas?These presentations focus on the Big Four Construction Hazards – falls, electrocution, caught-in and struck-by. All training materials will cover the four hazards seen regularly on construction sites and will focus on the methods for the recognition and the prevention of these common hazards. What are three ways an employer can protect workers from falls?What are the ways an employer can protect workers from falls? Guardrails, safety net system and personal fall arrest systems. How can we protect workers in the Unorganised sector?
What is the difference between a hole and an opening OSHA?So according to OSHA, not only is the location of a hole different than an opening (walking surface vs. wall), but so is the physical size of the void into which – or through – a worker may fall. What size hole requires a cover OSHA?First, §1926.501(b)(4)(i) requires that employees be protected from falling through holes more than 6 feet by fall arrest systems, guardrails or covers. So, if a hole is more than 6 feet deep, one of these protection systems must be used. At what diameter must floor holes be covered?Every floor hole into which persons cannot accidentally walk (on account of fixed machinery, equipment, or walls) shall be protected by a cover that leaves no openings more than one (1) inch wide. The cover shall be securely held in place to prevent tools or materials from falling through.
An opening at least 30 inches high and 18 inches wide, in any wall or partition, through which persons may fall, such as a yard-arm doorway or chute opening. Every stairway floor opening must be guarded by a standard railing (see the section Railing, Toeboard and Cover Specifications). What is an opening through which persons may fall?Floor opening What is being referred to in the following definition a barrier along the open sides of stairways and platforms that prevent falling OSHA?Terms in this set (10) What is being referred to in the following definition? A barrier along the open sides of stairways and platforms that prevent falling. Guardrail How wide does a catwalk need to be?The OSHA catwalk width requirements are found in section 1910.28(b)(5)(ii)(A). Under this provision, a catwalk or runway must be at least 18 inches wide. Which are the minimum dimensions of an opening that is described as a void or gap in a vertical surface?2 inches Is code for edge protection?Hs CodeDescriptionNo of Shipments3926Other Articles Of Plastics And Articles Of Other Materials Of Headings 3901 To 391439269099Other534016Other Articles Of Vulcanised Rubber Other Than Hard Rubber40169390Other136 more rows What protective device is required for a floor opening that measures at least 12 inches in at least dimensions?standard railing When must open sided floor or platforms be guarded by a standard railing?Every open-sided floor, platform or runway 4 feet or more above adjacent floors or ground level should be guarded by a standard railing on all open sides except where there is entrance to a ramp, stairway, or fixed ladder. What is the OSHA definition of a wall opening through which persons may fall?Opening means a gap or open space in a wall, partition, vertical walking-working surface, or similar surface that is at least 30 inches (76 cm) high and at least 18 inches (46 cm) wide, through which an employee can fall to a lower level. What is a through ladder?For through ladders, the steps or rungs are omitted from the extensions, and the side rails are flared to provide not less than 24 inches and not more than 30 inches of clearance (when a ladder safety system is provided, the maximum clearance between side rails of the extension must not exceed 36 inches). Which of the following is a fall prevention system?Terms in this set (10) What is being referred to in the following definition? A barrier along the open sides of stairways and platforms that prevent falling. Guardrail What is being referred to in the following definition a barrier along the open sides of stairways and platforms that prevent falling OSHA quizlet?Railing. A vertical barrier erected along exposed sides of stairways and platforms to prevent falls of persons. What is being described in the following definition an opening in the floor platform or pavement that measures 12 inches or more and through which persons may fall?Floor opening: an opening measuring 12 inches or more in its least dimension, in any floor, platform, pavement, or yard through which persons may fall; such as a hatchway, stair or ladder opening, pit or large manhole. What does the term floor hole mean?OSHA defines a floor hole as a gap or open space in a floor, roof, horizontal walking-working surface, or similar surface that is at least 2 inches (5 cm) in its least dimension. Which properly describes a floor opening a floor opening is an opening that?What properly describes a floor opening? A floor opening is an opening that: Measures at least 30 in.(762 mm) and 18 in. |
What protective device is required for a floor opening that measures at least 12 inches in its least dimension quizlet?
Postagens relacionadas
direito autoral © 2024 cemle Inc.
