If you notice that the water is cloudy in your lava lamp, its flow isn’t as lively as expected, or it's stopped moving at all, you're in the right place. This article tells you about the most effective ways that can help you restore your lava lamp. Show
Main Lava Lamps ProblemsA lava lamp is a fascinating decorative piece that can deliver not only illumination but much fun and entertainment as well. The exact makeup of lava is a secret but generally, it’s a blend of wax and oils that do not mix together. This combo is housed in a glass vessel with a halogen bulb underneath. This bulb heats up the wax within. Any lamp has a thoughtful design with a few inches left on the top for the gases that need some space for expanding. Liquids and wax have different densities and are completely insoluble with each other. And when you apply heat at the bottom (turn on the bulb), it produces liquid motion. When the wax absorbs the heat, it slowly expands. Once it happens, lava becomes less dense and slowly rises in the flowing motion. It takes approximately 40-50 minutes for the blobs of wax to form beautiful shapes. As soon as the wax cools down, it comes back at the bottom of the lamp again, forming a hole. However, if you notice that the flow isn’t as lively as expected, this means your lamp is
not working correctly. The most common issues owners have are clouded water and the lava stopped moving. Luckily, there are some things you can do to restore a lava lamp. Lava Lamp Stopped FlowingIf the lava in your lamp lies flat or isn’t flowing the way it should, you should try the following steps:
If no of the aforementioned methods can’t solve the problem, go to the following step. Run the lamp for at least four hours and then remove the globe from its stand. Use heat-resistant gloves to protect your hands. Place the globe on a flat surface and rotate it for a couple of minutes to break up the wax a little. Twirl the globe back in its base and let it heat up for one more hour. If all that fails and you understand that the wax won't move no matter what you do, you’ll need to turn to the manufacturer to replace the liquid. Lava Lamp Is CloudyIn case your lamp appears cloudy, here are some simple steps that can bring back the clarity: Method A Unplug the unit and leave it at room temperature for about eight hours. This will let the wax settle. Then turn the lamp on, wait until the lava begins to soften, and then shut it off again. After it cools, switch on the lamp and let it run for 8-10 hours. Method B Another way to tackle cloudy liquid is to unplug the lamp, let it cool for a few hours, unscrew the top cap and pour out all the liquid. You should only leave the solid wax ball at the bottom. Carefully fill the lamp with distilled water but don’t shake the lamp, since the wax is fragile. Pour the water out and repeat this procedure a few times. Finally, fill the vessel up with distilled water leaving a two-inch gap at the top. At this point, you shouldn’t put on the cap - just place the globe on the stand and run the lamp for an hour. At the same time, you should heat up a glass of distilled water and dissolve as much salt in it as possible. Dip a pipette into the saline solution and drop the inch of it into the lamp bottle once every 10 minutes. Allow it to diffuse on its own. As soon as the lava rises to the top, you can stop. Add a drop of dishwashing detergent
and two drops of food colorant to match the lava’s color. Screw the cap back and enjoy the beautiful flow. Lava Lamp Gets Too HotAs we’ve already mentioned, it’s prohibited to operate the lamp for more than ten hours at a time. And leaving your lava lamp for longer can cause it to overheat and even to become a fire hazard. The ingredients in the lamp need some time to harden and retain their integrity. If you’re a kind of forgetful person, you can use timers intended specifically for the lava lamps. Or you can always buy a couple of high-quality lava lamps if you need them to be on continuously. Take note that the lava lamp may get too hot if
the lava liquid stopped flowing and is resting at the bottom. If that goes for you, check the recommendations from the previous passages. Lava Lamp Wax Has Stuck at the Top of the BottleIn case there is some wax stuck at the top of a lamp after cooling down, it’s likely that your lava liquid has separated. That is to say, the less dense wax has separated from harder wax. This is a rather tricky problem to fix without ruining the integrity of the whole lamp. But impossible is nothing, and let’s check how to make things better.
Important Information about Lava LampsIf you’d like to prolong the life of your lava lamp, here are some important facts and recommendations about using the device.
How Long Do Lava Lamps Last on Average?Typically, it depends on the
lifespan of a bottle and bulb. While the bottle will last you about 2,000 hours if you handle it carefully, the life of the bulbs varies according to the usage. Anyway, you can always replace a dead bulb with a new one. Can Users Leave a Lava Lamp on All the Time?No! On no account must you leave your lava lamp on all the time. Of course, it’s quite tempting to watch the lava flowing in amoeba-like fashion all day and night long, but this can cause the lamp to overheat. And if the lamp overheats, the colored wax may form one large blob that won’t transform into other whimsical shapes. Ideally, 8-10 hours should be the limit for any lamp. Lava needs some time to cool down. But once it’s settled down and hardened, you can turn the lamp back on. It will function properly again. Still, it’s always better to check the manufacturer’s recommendations before use. Does Shaking a Lamp Ruin the Lava?When it comes to lava lamps, “Do not shake” is rule number one. Too much shaking can lead to cloudy appearance or, even worse, wax laying at the bottom in a big glob. So, do not shake your lamp and try not to move it from place to place. Keep it away from children's reach. If you follow our recommendations, you can expect your lamp working right for long years to come, providing you with enjoyment and endless serenity. Why is the lava in my lava lamp stuck at the bottom?This usually occurs when the lamp is overheated and needs a break from being on (don't ever leave your lava lamp on for over 10 hours). The halogen bulb should be checked if the lava is melting but lies flat. The bulb might be dead and in need of a replacement.
Why does the wax fall back to the bottom of the lava lamp?The wax expands when heated, and since density is equal to mass divided by volume, when the volume increases, the density of the wax decreases, and it floats. When the ball of goop reaches the top of the lamp it cools down, decreases in volume and thus density, and falls back to the bottom to begin its journey again.
Why won t the wax in my lava lamp move?Most issues with lava lamps can be remedied by warming up for 3-4 hours & turning off and let cool to room temperature. Repeat this until the problem is solved. We hope one of those tips helped you!
|